Aerial Tools & Equipment

10727

7″ Alloy Capstan: Mounts on 2 7/16″ dia. winch shaft. Super-strength, lightweight alloy has 50% greater strength than iron at half the weight. 7.25″ dia. x 8″ wide. Rating to 3500 lbs.

More Details

83669

RS Power Reel: 24.75″ OD x 6″ ID heavy-guage welded steel spool reinforced on exterior face. Mounts on either 18 9/16″ driving spindle connected to 2 7/16″ winch shaft or 13.25″ pole spindle to support spool at pole side for payout only. Spindle brake hub controls spool free wheelings. Extra spools are available. 12″ wide

More Details

83660

RS Power Reel: 24.75″ OD x 6″ ID heavy-guage welded steel spool reinforced on exterior face. Mounts on either 18 9/16″ driving spindle connected to 2 7/16″ winch shaft or 13.25″ pole spindle to support spool at pole side for payout only. Spindle brake hub controls spool free wheelings. Extra spools are available. 6″ wide holds 2000′ on .25″ rope

More Details

08136

CR Collapsible Power Reel: Mounts on 2 7/16″ dia. Winch shaft or capstan drive; holds 1,600 ft of rope or up to 200 lbs. of weight. Spindle has fixed and sliding spider with six rim segments. Fixed spider, yokes; segments are heat-treated aluminum alloy. Rated at 3,500 lbs. pull; ID: 20″; OD: 28″. Not to be used for storing mule tape or poly rope

More Details

24193

Extension Handles: Wire Raising Tool and Cable Block Lifter engage in female end of handle. Spring-mounted pin locks on tool or additional sections. Fiberglass Extension Handle 3′

More Details

24194

Extension Handles: Wire Raising Tool and Cable Block Lifter engage in female end of handle. Spring-mounted pin locks on tool or additional sections. Fiberglass Extension Handle 6′

More Details

JE-6/3

Extension Handles: Wire Raising Tool and Cable Block Lifter engage in female end of handle. Spring-mounted pin locks on tool or additional sections. Set of 4 foam core poles 21′

More Details

66003

Extension Handles: Wire Raising Tool and Cable Block Lifter engage in female end of handle. Spring-mounted pin locks on tool or additional sections. Head Section for Wire and Cable Cutter

More Details

66002

Extension Handles: Wire Raising Tool and Cable Block Lifter engage in female end of handle. Spring-mounted pin locks on tool or additional sections. Tapered diameter 1.75″x1.25″

More Details

66001

Extension Handles: Wire Raising Tool and Cable Block Lifter engage in female end of handle. Spring-mounted pin locks on tool or additional sections. 1.75″x6′

More Details

66000

Extension Handles: Wire Raising Tool and Cable Block Lifter engage in female end of handle. Spring-mounted pin locks on tool or additional sections. 1.25″x6′

More Details

WR-1

Wire Raising Tool: Plated steel wire raiser is designed for placing cable on rollers, construction blocks and hardware during line construction. Conveniently pulls or lifts branches out of dense foliage. No adapter needed. Not for use on or near live wires.

More Details

06355

Wire Raising Tool: A good all around tool that gives you the flexibility to place steel strand and aerial telephone wires at the same time. A hole on the shaft allows you to use the locking pin on either type of extension handle to hold the tool in place. Use with GMP Extension Handles (Lay-up Sticks)

More Details

71543

Multi-Angle Self Adjusting Corner Block: Adjusts istelf to a bending radius from 12″ max to a straight line to reduce friction when pulling cables around a corner. All aluminiumm heavy-duty construction. Attaches to a pole with an inclusive, steel chain binder

More Details

30292

Replacement Shoe for single-lashing aerial cable guide

More Details

91605

4″ Aerial Cable Guide: The Roller Type Aerial Cable Guide is used to guide and straighten cables as they are pulled into a lashing position from a stationary or moving cable reel. With its 3 sheaves to guide cable with minimum friction, this is the best tool you can use when handling especially heavy cable, or when using an aerial basket for “drive-off” lashing .The guide rides along the strand on a roller bearing for smooth movement A built in grip prevents back rolling during span transfers. Also included with the guide is a safety chain to prevent the guide from coming off the start. For 4″ cable or bundles to 4″. These cable guides have 2 rollers instead of the rubber grip and they do not require the use of the hitch weldment or hitch field kit

More Details

70055

Single-Lashing Aerial Cable Guide: This guide is economical but durable for new plant construction only. It has a 2.75″ cable capacity. Cable shoe has a unique non-stick, highly polished stainless steel surface to minimize cable friction. Replaceable shoe makes it easy to keep the guide like new

More Details

08007

Dual-Lashing Aerial Cable Guide: this guide is used to guide and straighten cables as they are pulled into a lashing position from a stationary or moving cable reel. A cast aluminum shoe with a steel insert on the face provides longer wear life; the shoe is suspended on steel straps from two strand rollers with safety lock preventing it from falling from the strand

More Details

01384

Speedigrip: Visegrips equipped with jaws for temporarily securing lashing wire. Adjustable to any cable size

More Details

70626

Cable Pulling Sled with Swivels: The pulling sled is used for aligning two or three cables in the multiple cable block and pulling overhead cable into position prior to lashing. It incorporates either a 5000 or 7500 lb swivel capacity on the front and three 5000 lb swivel capacity on the rear. It is generally used with any conventional winching device. The 22″ chain provides both alignment and stability.

More Details

Ready To Order?

© 2022 Brenco Power Line Tools